White
Showing 41–60 of 150 results
Filtri
The data on this page are to be considered purely indicative and do not constitute a technical data sheet.
-
- Cures at room temperature
- Pasty consistency
- It does not drip
- Easy to apply
- High elongation
- Stable and flexible over a wide temperature range
-
- Can be used in corrosion-sensitive electrical equipment and PCB systems without adverse effects
- Easy to handle
- UL Classified
- Non-corrosive
- Low odor
- Cures at room temperature
-
- 100% silicone
- Superior adhesion to a wide variety of surfaces
- Low odor
- Neutral polymerization (alcohol)
- Does not corrode metal or other sensitive materials
- Forms a flexible and long-lasting seal
-
- Two-component adhesive sealant
- Rapid polymerization at room temperature
- Neutral alkoxide polymerization
- Pasty, non-self-levelling consistency
- Good and durable adhesion
- Excellent weather, UV and heat resistance up to 190°C
- Rapid curing allows rapid handling of bonded components
- Deep polymerization
-
- Two-component adhesive sealant
- Rapid polymerization at room temperature
- Neutral alkoxide polymerization
- Pasty, non-self-levelling consistency
- Good and durable adhesion
- Excellent weather, UV and heat resistance up to 190°C
- Rapid curing allows rapid handling of bonded components
- Deep polymerization
-
No mixing required No exotherm of reaction during curing Excellent adhesion without primer on many substrates Excellent performance over a wide temperature range Polymerizes into low-stress soft elastomers Controlled volatility (controlled migration of silanes)
-
- Meets BS 476 Part 22 standard
- Excellent primerless adhesion on most substrates
- porous and non-porous buildings
- It does not drip
- Joint movement capacity ±50%
- Neutral curing system
- Halogen-free
- Complies with ISO 11600-F&G-25LM Standard
- A fire resistance value of up to 4 hours can be obtained
- Extensively tested on many European specifications
- Out of footprint in 1.5 hours
- Excellent weathering characteristics, including resistance to ozone, UV radiation and extreme temperatures
- Long service life
- CE marked as fire resistant according to ETAG 026
-
- Superior sealing characteristics when exposed to fuels and oils
- Easily injected and reinjected
- Does not harden
- Good grip
- Essentially unaffected by shock, vibration, and thermal cycling
- Contains no hardeners or curing agents
- Withstands immersion in fuels and exposure to fuel vapors at temperatures up to +200°C
- Contains flow control particles
- Excellent flow characteristics allow faster injection at lower pressures.
-
- Moderate thermal conductivity
- One part: no ovens or curing required
- Pulls heat away from critical components
-
- Mellow
- Two-component - 10:1 mixing ratio
- High tensile strength
- Good processing time after mixing
- Hot polymerization
-
- Polymerization at room temperature
- Good adhesion on various substrates
- Fast tack-free time
- Elastomeric material with high elongation
- Suitable for bonding, sealing and thermal dissipation
- Good mechanical strength
-
- One-component adhesive
- Thermally conductive
- Polymerizes with moisture
- Fast drying to the touch
- Good adhesion
- Self-leveling
- Controlled volatility (controlled migration of silanes)
-
- Rapid polymerization in RT
- Low viscosity
- Controlled volatility of silicone
- No solvent added
-
- Rapid polymerization in RT, without notches
- Not smooth
- Higher thermal conductivity
- Controlled volatility of silicone
- No mixing required
- Polymerization at room temperature
- Faster processing at room temperature
- Used if increased flame resistance is required
-
- Rapid polymerization in RT
- Mellow
- High elongation
- Controlled volatility of silicone
- Single-component - No mixing required
-
- Volatility-controlled silicone
- Polymerizes into a soft and elastic elastomer
- No solvent added
- Single-component - No mixing required
- Polymerization at room temperature
-
- Cures at room temperature when exposed to air humidity
- Acetoxy polymerization system
- Pasty and non-sagging consistency
- Easy to apply
- Good adhesion on many substrates
-
- Can be used as a printable PAD
- Can replace the traditional manufactured pad
- Use as a gap filler
- Dispensed or printed through manual or automated processes
- Deposit of features for precise coverage of components
- Lower cost of ownership than manufactured pads
- Excellent thermal performance
- Soft, stress-relieving and shock-dampening
- Reworkable
-
- Good thermal conductivity
- Low oil bleed
- Stable at high temperatures
-
- High thermal conductivity
- Optimal heat dissipation
- Low viscosity for easy application
- Used as thermal interface material
- Based on a non-silicone oil
- Avoids migration problems of silicone and siloxane LMW
- Non-curing paste
- Enables simple and efficient rework of components
