Electronics

Showing 1–20 of 28 results

Text search

Tipo di prodotto

Marchio

Tecnologia

Applicazioni

The data on this page are to be considered purely indicative and do not constitute a technical data sheet.

Read more Quick View
CRC Contact Clean & Protect
- Electrical contact cleaning oil
- Removes corrosion and oxidation (oxides, sulfates, sulfides, carbonates)
- Dissolves grease, oil, and resinous contamination
- Rapid evaporation
- Non-corrosive
- Contains corrosion inhibitor
- Provides long-lasting lubrication
- Protects contacts after cleaning
- Safe on metal surfaces (non-staining)
- Safe on most rubbers, plastics, and coatings
- (preliminary testing recommended on sensitive materials)
- 360° spray valve (can be used upside down)
- High-purity CO₂ propellant (95% active content)
- Do not use on energized equipment
- Professional technical spray
Read more Quick View
CRC Contact Cleaner
- Precision cleaner for electrical and electronic contacts
- Removes dirt, residues and contaminants from contacts
- Leaves no residue after application
- Fast drying
- Suitable for cleaning electronic boards
- Specific for electrical and electronic equipment
- Non-corrosive
- Developed for components that do not tolerate aqueous cleaners
- Do not use on energized equipment
- Professional technical spray
Read more Quick View
DOWSIL™ 3-6548 Silicone RTV Foam
- Two-component fire-resistant RTV silicone foam
- Two-component room temperature vulcanizing (RTV) silicone foam
- Fire resistant
- Good flexibility even under severe operating conditions
- Withstand high temperatures
- Designed to limit hazards such as smoke, flames and gases.
- Expands and cures at room temperature to form a closed-cell foam elastomer.
- Designed for creating fire-resistant seals in penetrations and linear joints.
Read more Quick View
DOWSIL™ 3810 EG
- One-part dielectric gel
- Transparent
- Hot polymerization
- Low viscosity
- Very soft gel
- Suitable for PCB potting and electronic component protection
- Electrical insulation and environmental protection
- Extended temperature range (-60°C / +200°C)
- No mixing required
Read more Quick View
DOWSIL™ 4535
- No exotherm during curing
- Room temperature or heat-accelerated polymerization
- High stability during thermal cycles up to 150°C (peak 175°C)
- Maintains vertical position
- Controlled low silicone volatility
- Soft and elastomeric material after polymerization
Read more Quick View
DOWSIL™ 5351
- Non-curing
- High thermal conductivity
- Stable on vertical surfaces
- Gap filling capacity up to 1.0 mm
- Thermally conductive silicone material
- Low thermal resistance and good high-temperature stability
Read more Quick View
DOWSIL™ 5515
- Low density
- Room temperature or heat-accelerated polymerization
- Non-sagging, stable even on vertical surfaces
- Soft and deformable material with stress relief function
- Slightly tacky surface after curing
- No exotherm during curing
Read more Quick View
DOWSIL™ 5888
- Non-curing
- High thermal conductivity
- Low thermal resistance
- Solvent-free formulation
- Thixotropic - low flowability
- Applicable via screen printing, stencil or dispensing
- Ability to achieve thin thicknesses
Read more Quick View
DOWSIL™ CC 2588
- Medium viscosity
- Abrasion-resistant elastoplastic surface
- Solvent-based coating
- High solid content
- UV indicator for inspection
- Room temperature vulcanization (RTV)
- Good adhesion on rigid and flexible PCBs
Read more Quick View
DOWSIL™ CC 8030 UV
- Low viscosity, spray applicable
- Fast UV cure with secondary moisture cure
- Solvent-free
- UV indicator for inspection
- Good adhesion to PCB materials
- Reduced oxygen inhibition
Read more Quick View
DOWSIL™ EC-8425
- High electrical conductivity (silver-based filler)
- Electromagnetic shielding (EMC) over a wide frequency range
- High elongation for stress relief (>20%)
- Non-slump adhesive (non-flowable)
- UV traceability for inspection
- Good adhesion on various substrates
- Solvent-free formulation
Read more Quick View
DOWSIL™ SE 4420
- Polymerization at room temperature
- Good adhesion on various substrates
- Fast tack-free time
- Elastomeric material with high elongation
- Suitable for bonding, sealing and thermal dissipation
- Good mechanical strength
Read more Quick View
MG Chemicals 8329TCM
- Thermal conductivity of 1.4 W/(m-K)
- Mixing ratio 1:1
- Processing time: 45 minutes
- Cure time: 24 hours at room temperature or 1 hour at 65 °C (149 °F)
- Provides strong electrical insulation
- High mechanical strength
- Strong resistance to moisture, salt water, light bases and aliphatic hydrocarbons
Read more Quick View
MG Chemicals 8329TFF
- Thermal conductivity of 0.8 W/(m-K)
- Mixing ratio 1:1
- Fire retardant - UL 94V-0 registered
- Processing time: 5 minutes
- Laying time: 15 minutes
- Provides strong electrical insulation
- Low CTE before Tg
- High tensile and compressive strength
- Strong resistance to moisture, salt water, light bases and aliphatic hydrocarbons"
Read more Quick View
MG Chemicals 8330D
- Extreme electrical conductivity
- Convenient 1-to-1 mixing ratio
- Processing time: 20 minutes
- Cure time: 6 hours at room temperature or 10 minutes at 65 °C (149 °F)
- Creates strong permanent electrical connections
- Polymerization at room temperature
- Without SVHC
- Excellent adhesion to many substratesStorage at room temperature
- Long shelf life
- Strong resistance to moisture, salt water, light bases and aliphatic hydrocarbons
Read more Quick View
MG Chemicals 8330S
- Low outgassing approved by NASA
- Extreme electrical conductivity
- Convenient 1-to-1 mixing ratio
- Working time: 4 hours
- Cure time: 2 hours at 65 °C (149 °F) or 30 minutes at 100 °C (212 °F)
- Creates strong permanent electrical connections
- Excellent adhesion to many substrates
- Storage at room temperature
- Long shelf life
- Strong resistance to moisture, salt water, light bases and aliphatic hydrocarbons
Read more Quick View
MG Chemicals 8331D
- High electrical conductivity
- Convenient 1-to-1 mixing ratio
- Processing time: 20 minutes
- Cure time: 6 hours at room temperature or 10 minutes at 65 °C (149 °F)
- Creates strong permanent electrical connections
- Polymerization at room temperature
- Without SVHC
- Excellent adhesion to many substrates
- Storage at room temperature
- Long shelf life
- Strong resistance to moisture, salt water, light bases and aliphatic hydrocarbons
Read more Quick View
MG Chemicals 8331S
- Low outgassing approved by NASA
- High electrical conductivity
- Convenient 1-to-1 mixing ratio
- Working time: 4 hours
- Cure time: 2 hours at 65 °C (149 °F) or 30 minutes at 100 °C (212 °F)
- Creates strong permanent electrical connections
- Excellent adhesion to many substrates
- Storage at room temperature
- Long shelf life
- Strong resistance to moisture, salt water, light bases and aliphatic hydrocarbons
Read more Quick View
MG Chemicals 838AR
- Provides >52 dB RFI shielding at frequencies <1 MHz
- Excellent adhesion to plastics
- Strong corrosion resistance
- Gentle solvent system, safe on polystyrenes
- HAP-free: does not contain toluene or xylene
Read more Quick View
MG Chemicals 841AR
- UL Recognized (File No. E202609)
- Provides effective EMI/RFI shielding over a wide range of frequencies
- Strong corrosion resistance
- Gentle and safe solvent system on polystyrenes
- HAP free-does not contain toluene, xylene, or MEK
- Available in aerosol format